Skip to main content

YAML in Semiconductor EDA: From Configuration Language to Reusable Design-Flow Methodology

Hello Dear Readers,   Today in this post, I will provide some deep insight about yaml langauge for CAD flow developments with detailed examples. YAML is not a programming language in the same sense as Python, Tcl, C++, or Verilog. It is primarily a human-readable data serialization/configuration language . In semiconductor EDA, that distinction is important because YAML generally describes what a flow should do , while Python/Tcl/Shell and the EDA tools execute the flow . The official YAML specification describes it as a data serialization language designed to be human-friendly and portable across programming languages. For the semiconductor angle, this becomes particularly interesting because YAML can act as a configuration layer between design methodology and EDA implementation . Frameworks such as Hammer explicitly use YAML/JSON configuration and an intermediate representation to standardize information exchanged between design, technology, and tool plugins. 1. Introduction M...
1 comment

CMOS Logic Gates Using Verilog HDL

  CMOS Logic Gate Design 

Hello Dear Readers,

This section describes how to used a low-level CMOS transistor to design basic digital logic gates and its implementation in Verilog HDL.

In CMOS technology, both PMOS as well as NMOS transistors, are used. PMOS is active when the input signal will be 0(Low) level, and NMOS is active when the input signal will be 1(High) level. In below figures show the basic design of the CMOS inverter, NAND, NOR gates. We know if we made AND or OR gate from NAND or NOR respectively, then we need two more transistors of the inverter. That's why we see in the gate array chips contain an array of the universal gates only.




In the below section, I have written the whole Verilog code of all the gates with testbench code.

Verilog Code:

module CMOS_Gates(input a,b,output f,f1,f2
    );
supply1 vdd;
supply0 gnd;
wire w1,w2;

//NOT gate
// pmos (drain, source, gate);
pmos t1 (f, vdd, a);
// nmos (drain, source, gate);
nmos t2 (f, gnd, a);

//NAND gate

// pmos (drain, source, gate);
pmos t3 (f1, vdd, a);
pmos t4 (f1, vdd, b);
// nmos (drain, source, gate);
nmos t5 (f1, w_n, a);
nmos t6 (w1, gnd, b);

//NOR gate

// nmos (drain, source, gate);
nmos t7 (f2, gnd, a);
nmos t8 (f2, gnd, b);
// pmos (drain, source, gate);
pmos t9 (w2, vdd, a);
pmos t10 (f2, w2, b);

endmodule

module tb();
reg a,b;
wire f;
CMOS_Gates DUT (a,b,f,f1,f2);
initial 
begin
   a=0; b=1;
#1 a=1; b=0;
#1 a=0; b=1;
#1 $finish;
end
initial 
begin
$monitor("%2d:\ta = %b\tb=%b\tf = %b\tf1 = %b\tf2 = %b",$time,a,b,f,f1,f2);
end
endmodule
 
Here supply0, supply1, pmos, and nmos are keywords that stand for ground, power supply, PMOS transistor, and NMOS transistor, respectively. Here testbench program is also written with an input signal a,b, and output f,f1,f2 is corresponding to the NOT, NAND, NOR gate.

Thanks for Reading,
If you have any doubts related to this Verilog code, just write them in the comments. I will be giving a reply as soon as possible.



Labels:
Location: India

Comments

  1. Anonymous5 January 2021 at 05:15

    Wow sir great start keep it up.

    ReplyDelete
  2. Unknown6 January 2021 at 04:18

    Good sir now we are waiting project type code🤗🤗🤗🤗🤗🤗🤗

    ReplyDelete
  3. Anonymous9 January 2021 at 19:01

    Nice post

    ReplyDelete

Post a Comment

Popular posts from this blog

Signal Electromigration (Signal EM): Violations, Examples, and Practical Fixes

  Hello Dear Readers,   Today in this post, I will provide some deep insight into the Signal Electromigration (Signal EM): Violations, Examples, and Practical Fixes. 1. Introduction: As technology nodes shrink into the deep‑submicron and nanometer regime (7nm, 5nm, 3nm and beyond), electromigration (EM) has become a first‑order reliability concern—not only for power/ground (PG) networks but also for signal nets. Signal EM failures are often underestimated because signal currents are transient and bidirectional. However, with higher switching activity, tighter metal pitches, thinner wires, and aggressive timing closure, signal EM can cause latent or early‑life failures if not addressed properly. This article explains: What Signal EM is and how it differs from PG EM Typical Signal EM violation scenarios Detailed, practical examples Root causes behind each violation Proven solutions and best practices to fix and prevent Signal EM issues 2. What is Signal Electromigration: El...
Post a Comment
Read more

Exploring the Role of LEF Files in VLSI Chip Design: A Beginner's Guide

Hello Dear Readers,   Today in this post, I will provide some deep insight into the LEF file role during the VLSI Chip Design process. In VLSI (Very Large Scale Integration) design, a LEF file is a file that contains information about the physical geometry of the standard cells used in a circuit. LEF stands for Library Exchange Format. A standard cell is a pre-designed logic cell that contains a specific function, such as a flip-flop or an AND gate. Standard cells are designed to be easily combinable and scalable to create more complex circuits. The physical geometry of each standard cell is defined in the LEF file. The LEF file contains information such as the width, height, and position of the pins and metal layers of each standard cell. It also contains information about the physical design rules that govern the placement of these cells on the chip. LEF files are important in VLSI design because they enable the interoperability of different design tools from different vend...
4 comments
Read more

Power Analysis in the VLSI Chip Design

  Hello Dear Readers,   Today in this series of posts I will provide some deep insight into Power Analysis in the VLSI Chip Design. The power analysis flow calculates (estimates of) the active and static leakage power dissipation of the SoC design. This electrical analysis step utilizes the detailed extraction model of the block and global SoC layouts. The active power estimates depend on the availability of switching factors for all signals in the cell netlist. Representative simulation test cases are applied to the netlist model, and the signal value change data are recorded. The output data from the power analysis flow guide the following SoC tape out release assessments:  Total SoC power specification (average and standby leakage): The specification for SoC power is critical for package selection and is used by end customers for thermal analysis of the product enclosure. In addition to the package technology selection, the SoC power dissipation is used to ev...
5 comments
Read more